PRODUCT DESSCRIPTION:
- MC-DUR 1022 is a two-component solvent based, Epoxy resin coating system supplied in pre-weighed packs ready for on-site mixing and use.
- The cured film forms a hard but flexible coating with excellent adhesion to clean concrete, sand/cement and granolithic screeds, and certain metal surfaces. It cures to a semi-gloss, impervious finish which is easily cleaned.
- The product is available in a range of standard colours and is also available in a clear grade.
- Standards compliance: MC-DUR 1022 complies with BS 476, Part 7: 1971 – Class 1 spread of flame.
PRODUCT PROPERTIES:
- Hard wearing – durable, low maintenance costs.
- High resistance to a wide range of industrial chemicals.
- Hygienic – impervious finish provides easily cleaned surface.
- Attractive – available in a range of colours to improve the working environment.
AREAS OF APPLICATION:
- To provide a hard wearing, easily cleaned, attractive floor coating in areas where high resistance to chemical attack is required. It is suitable for use in production assembly areas, workshops, dairies, soft drinks production and bottling plants, kitchens, showrooms etc. It is particularly suitable in wet working areas and where chemical spillage is likely, e.g. plating shops, processing plants, dye works etc.
- It can also be used as a final coating and sealer for epoxy floor screeds to provide a more durable and easily cleaned surface where high impact is desirable.
- A clear version is also available to seal Terrazo and other type of floors. Typical areas of application include:
– Airport Lounge, terminals etc.
– Hospitals
– Shopping malls & convention centres
– Pharmaceuticals plants
– Educational institutions
– Residential/Commercial buildings
Chemical properties: MC-DUR 1022 is resistant to a wide range of chemicals. Few of them are listed below. Specific data will be available upon request.
Sodium hydroxide 25% : Resistant Citric Acid 10% : Resistant
Hydrochloric Acid (10%) : Resistant Lactic Acid (10%) : Resistant
Phosphoric acid (10%) : Resistant Petrol : Resistant
Engine Oil : Resistant Sulphuric Acid (10%) : Resistant
Note: Colour change may occur but no change in protective performance. Good housekeeping is essential in areas where chemical spillage is likely to occur. It is especially important that such spillage should not be allowed to dry since very much higher concentrations of chemicals will then result.
PRODUCT CHARACTERISTICS:
| Coverage | MC-DUR 1022: 10 m²/litre @ 100 microns wft per coat (2 coat application recommended)
Note: Coverage figures given are theoretical – due to wastage factors and the variety and nature of substrates, practical coverage figures may be reduced, this will vary with site and application conditions. |
| Estimating supply | MC-DUR 1022 (Including colour pack): 4.5 litre/ packs |
| Shelf-life & Storage | MC-DUR 1022 have a shelf-life of 12 months if kept in a dry store between 5°C and 30°C in the original, unopened packs. All products should be stored in accordance with local regulations. |
| Precautions Health and safety | MC-DUR 1022 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapours. Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used. The use of barrier creams provide additional skin protection.
In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting. |
| Fire | MC-DUR 1022 are flammable. Keep away from sources of ignition. No smoking. In the event of fire, extinguish with CO2 or foam. Do not use a water jet. |
| Flash points | MC-DUR 1022: 23°C |
| Disposal | Spillages of component products should be absorbed onto earth, sand or other inert material and transferred to a suitable vessel. Disposal of such spillages or empty packaging should be in accordance with local waste disposal authority regulations. |
PHYSICAL PROPERTIES:
| @ 25oC | @ 35oC | |
| Pot life* | 4 hrs | 1.5 hrs |
| Time between coats | 6-24 hrs | 4-16 hrs |
| Initial hardness | 24 hrs | 18 hrs |
| Full cure | 7 days | 5 days |
| Wet film thickness (per single coat) | 100 microns | |
| Total dry film thickness (2 coats) | 90 microns | |
Note: After the pot life has expired, the material, although not hardened, increases in viscosity and the characteristics of the product change. Excess material should be discarded after this point.
